宝贝描述:
Klubersynth GH 6-(32,80,150,220,320,460,680,1000)合成高温齿轮油。
说明:Klübersynth
GH6高温聚乙二醇齿轮油基础。他们有增加的划伤提供良好的负载能力和保护,防止磨损。严格的FZG试验(A/16.6/140),这些油有划伤加载阶段>
12并在重量与工作有关的损失≤0.2毫克/千瓦时。 Klübersynth GH6特别是抗老化和氧化,他们有一个良好的粘温关系并显示出优异的高温行为。
应用领域:Klübersynth
GH6特别是制定了蜗杆与齿轮润滑钢/铜配对。在这应用程序有两个有趣的方面:特殊的聚乙二醇基地油降低了摩擦系数,和非常有效的添加剂大限度地减少磨损。Klübersynth
GH6也适用润滑所有类型的斜面与正齿轮,滑动与滚动轴承以及齿联轴器,特别是当接触到温度升高。
特性:
合成齿轮高温油
优异的粘温的关系
宽工作温度的范围
减少摩擦
高划伤负载能力
良好的抗磨损性能。
包装规格:20升罐200升鼓
德文:
Klübersynth GH 6 Oils
Synthetic gear and high-temperature
oils
Description:
Klübersynth GH 6 oils are high-temperature
gear oils
on a polyglycol
basis. They have an increased scuffing
load capacity and
provide good
protection against wear. In the stringent
FZG test
(A/16.6/140) these
oils had a scuffing load stage > 12
and a
work-related loss in weight
≤ 0.2 mg/kWh. Klübersynth GH 6
oils are
particularly resistant to
ageing and oxidation, they have a
good
viscosity-temperature relationship
and show an excellent
hightemperature
behaviour.
Fields of application:
Klübersynth GH 6 oils
were
especially developed for the
lubrication of worm gears
with
steel/bronze pairings. In this
application there are two
interesting
aspects: the special polyglycol base
oils reduce the friction
coefficient,
and the very efficient additives
minimize
wear.
Klübersynth GH 6 oils are also suitable
to lubricate all types of
bevel
and spur gears, plain and rolling
bearings as well as toothed
couplings,
especially when exposed to
increased
temperatures.
Application notes:
Klübersynth GH 6 oils can be
applied
by immersion, immersion
circulation and injection. Observe
the
manufacturer’s instructions
about the maximum viscosity that
can be
pumped.
Klübersynth GH 6 oils are not miscible
with mineral oils and
synthetic
hydrocarbons. We recommend
cleaning the lubrication points
prior
to conversion, and rinsing gears or
closed lubricating systems with
the
Klübersynth GH 6 oil that will be
used for lubrication.
Klübersynth
GH 6 oils are neutral
towards ferrous materials and
almost all nonferrous
metals. There
may be increased wear when the
contact surfaces of design
elements
made of aluminium or aluminium
alloys are exposed to dynamic
loads
(sliding speed and high loads). If
necessary, wear tests should
be
carried out.
Depending on temperature and
exposure time, synthetic
lubricants
on a polyglycol base may have an
impact on the functional
capacity of
rubber-elastic sealing materials.
Seals made of NBR
materials
(acrylonitrile-butadiene-rubber) can
be used at permanent
temperatures
up to 100 °C. For higher temperatures
we recommend to use
seals
made of FKM materials (fluorinated
rubber), i. e. elastomers which
are
resistant to Klübersynth GH 6 oils.
It has to be taken into
ac
that different elastomer qualities
produced by one manufacturer
or
different manufacturers may show a
different behaviour. For
approximate
values about a change in volume
and hardness of NBR and
FKM
materials in contact with Klübersynth
GH 6 oils refer to the
table
“compatibility with elastomers”.
Paints may be attacked by
synthetic
lubricants. When applying Klübersynth
GH 6 oils we recommend
the
use of two-component paints (reactive
paints) for interior coating.
Oil
gauge glasses should preferably be
made of natural glass or
polyamide
materials. Other transparent
plastics, e. g. Plexiglas, have
a
tendency to crack under stress.
We recommend testing the
suitability
of design materials and paints in
contact with the ed
lubricants,
especially for series application.
Viscosity ion for
rolling
bearings and gears:
ion of the correct oil
viscosity for
rolling bearings
To the correct oil viscosity
observe the bearing
manufacturer’s
instructions or refer to GfT worksheet
3 (GfT = Society of
Tribology).
For determining the existing viscosity,
refer to the enclosed
viscositytemperature
diagram indicating the
differing
viscosity-temperature
behaviour of Klübersynth GH 6 oils
as compared to
mineral oils.
ion of the correct oil
viscosity for gears
The
manufacturer’s instructions take
priority in all cases.
The correct
viscosity can also be
ed in accordance with the
enclosed worksheet
“Klübersynth
GH 6 oils – ion of oil viscosity
for gears”.
Service
temperature range:
Gear and chain lubrication by
immersion:
Klübersynth
GH 6-32:
from approx. – 45 °C to 160 °C
Klübersynth GH 6-80 … 150:
from
approx. – 35 °C to 160 °C
Klübersynth GH 6-220 and -320:
from approx. – 30
°C to 160 °C
Klübersynth GH 6-460 … 1000:
from approx. – 25 °C to 160
°C
Klübersynth GH 6-Oils
Synthetic gear and
hightemperature
oil
Excellent viscosity-temperature
relation
Wide
service temperature
range
Reduces friction
High scuffing load
capacity
Good antiwear properties
|